Member Homepage for eugene-ksf-

eugene-ksf-

Name:

Mr.

Web Site:

replace Pages:

See also:

Yet another software implementation of RS-232 routines: any baud rate at any clock frequency (up to F/10); CTS/RTS flow control.
Maximum speed achived @ 4 Mhz is 230400.

Bit timing errors

Clock/Rate	4 MHz	10 MHz
57600	2.7%	1.0%
115200	5.1%	2.3%
230400	8.8%	4.1%
460800	23%	8.3%
921600	-	16%

replies: ?+

Code:

shares this code:

http://piclist.com/techref/member/eugene-ksf-/rs.asm

	TITLE "Example on using RS_bodySEND, RS_bodyRECEIVE macros"
;------------------------------------------------------------
;      Copyright: Eugene M. Hutorny © 2003,eugene@ksf.kiev.ua
;      Revision:  V0.01
;      Date:      Feb 25, 2003
;      Assembler: MPASM version 3.20.07
;------------------------------------------------------------
; Example on using RS_bodySEND, RS_bodyRECEIVE macros
;------------------------------------------------------------
			include         "p16f84a.inc"
			include			"rs.inc"
			
#define CLOCK 		.4000000
#define	RX	PORTB,0			; RX Pin,  RB0, input 
#define	TX	PORTB,1			; TX Pin,  RB1, output
#define CTS PORTB,2			; CTS pin, RB2, output 
#define RTS PORTB,6			; RTS pin, RB6, input
#define	RS_BITCOUNT	.8
#define RS_BUFFSIZE .16

	UDATA
TMP_WREG	res 1			; temporary storage for WREG
TMP_STATUS	res 1			;          - " -        STATUS
RS_DATA		res 1			; file register used in RS
RS_COUNT	res 1			; bit counter
RS_ALIGN	res 1			; alignment bits
RS_COUNTER	res 1			; recieved/echoed counter
RS_BUFFER	res RS_BUFFSIZE	; data buffer

nope	macro		; nop 2 cycles long
	goto $+1		
  endm
  
RS	CODE
RS_SEND
	RS_bodySEND .115200, RS_BITCOUNT, TX, 0
	return	

;---------------------------------------------------------------------------
RS_READBUFF					; READ incoming data to buffer
	bcf		INTCON, INTF
	bsf		INTCON, INTE
	bsf		INTCON, GIE
	bcf		CTS				; transmission shall begin
	clrf	TMR0			; clear timer
	bcf		INTCON, T0IF	; clear timer expiration flag
rx	clrwdt
	btfsc	RTS				; is RTS kept SPACE
	goto	suspend			; no, suspend reception
	tstf	RS_COUNTER		; test is something received
	skpnz					
	goto	rx				; if no bytes yet received, just wait
	btfsc	INTCON, T0IF	; if timer expired
	goto	suspend			; suspend reception
	tstf	RS_COUNTER		; test RS_COUNTER
	skpnz					; if( RS_COUNTER > 0)
	goto	rx				; continue reception
suspend	
	bsf		CTS				; request suspending reception
	clrf	TMR0			; clear timer
	; relaxation period after last byte recived
xr	clrwdt
	movlw	RS_BUFFSIZE - 1
	subwf	RS_COUNTER, W	; RS_COUNTER - (RS_BUFFSIZE - 1)
	skpnc					; if( RS_COUNTER - (RS_BUFFSIZE - 1) > 0)
	goto	readdone					
	btfsc	RTS				; wait if space is kept SPACE
	goto	readdone					
	btfss	TMR0, 2			; time out = 4 timer ticks (1024 IC) ~ 1 ms, good for fast PC's
	goto	xr
readdone
	bcf		INTCON, GIE
	bcf		INTCON, INTE	; disable INT interrupt
	return		

RS_INTERRUPT				; interrupt on RX entry
	movwf	TMP_WREG		; 6: save W
	swapf	STATUS, W		; 7: load STATUS
	movwf	TMP_STATUS		; 8: save STATUS
	bsf		CTS				; 9: request suspending reception
	RS_bodyRECEIVE .115200, RS_BITCOUNT, RX, 0, INDF, .9, -.3
	clrf	TMR0			; 75: clear timer
	incf	FSR, F			; 76: forward buffer pointer
	incf	RS_COUNTER, F	; 77: count this byte
	swapf	TMP_STATUS, W	; 78:
	movwf	STATUS			; 79: restore STATUS
	swapf	TMP_WREG, F		; 80:
	swapf	TMP_WREG, W		; 81: restore W
	bcf		INTCON, INTF	; 82: interrupt handled
	retfie					; 83: leave routine - 2 cycles of one stop bit left

	RS_delays
	END

shares this code:

http://piclist.com/techref/member/eugene-ksf-/rs.inc

	SUBTITLE "RS-232 Definitions"
;
;------------------------------------------------------------
; File Name :      RS.inc
;------------------------------------------------------------
;      Copyright: Eugene M. Hutorny © 2003, eugene@ksf.kiev.ua
;      Revision:  V0.01
;      Date:      Feb 25, 2003d
;      Assembler: MPASM version 3.20.07
;------------------------------------------------------------
;
;------------------------------------------------------------
; This file contains macro that expands to RS procedures
; Usage: 
;	1. Define CLOCK, CTS', RTS'
;   2. include into your ASM file
;	3. Define RAM locations RS_DATA, RS_ALIGN, RS_COUNT
; 	4. Place RS_body macro in your code
;	5. Place RS_delays in your code
; Requires definitions of: 
;		CLOCK, CTS', RTS'
; Requires visibility of RAM locations: 
;		RS_DATA, RS_ALIGN", RS_COUNT"
; Note' Only if CTS/RTS control turned on by RS_OPTION_CTSRTS
; Note" For low speed only (bit longer 10 cycles)
;------------------------------------------------------------

; RS_232 options
#define RTS_SPACE_LEVEL	0
#define CTS_SPACE_LEVEL	0

; Hardware flow control is implemented in software on PC
; Doc on 16550 UART (PC16550D.pdf by NS) says:
; CTS, Clear to Send, Pin 36: When low, this indicates that
; the MODEM or data set is ready to exchange data. The CTS
; signal is a MODEM status input whose conditions can be
; tested by the CPU reading bit 4 (CTS) of the MODEM Status
; Register. Bit 4 is the complement of the CTS signal. Bit 0
; (DCTS) of the MODEM Status Register indicates whether
; the CTS input has changed state since the previous reading
; of the MODEM Status Register. 
; CTS has no effect on the Transmitter.
; ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

;------------------------------------------------------------
;
; This macro calculates RS constants for transmitter or reciver
; at specified speed and number of bits 
; requires CLOCK to be defined (in hertz)

RS_calcCONST macro speed, bits, rcv
  local cycles, align, half
  local i, c
cycles = CLOCK / (speed / .25) ; ((CLOCK / 4) / speed ) * 100
half = CLOCK / (.2 * speed / .25)
RS_CYCLESPERBIT set cycles / .100
RS_HALFCYCLE set half / .100
i = 0
c = RS_HALFCYCLE * rcv
align = 0
  while( i <= bits )		; bit alignment for all bits + stop bit
c = c + RS_CYCLESPERBIT
i++
   if( (i * cycles + (half - .25) * rcv) - (c * .100) >= .50 )
align = align | (1 << (i-1) )  
c++
   endif
 endw
RS_BITALIGNMENT set align
 endm

;------------------------------------------------------------
; This macro generates code for the specified delay (in cycles)
; valid values are 0-1028, gurantied precision - 1 cycle
; delays 0-3 are generated inline, 4-8 - call RS_DELAY(N)IC
; 9 and higher - call RS_DELAY(0-3)WC, WREG is loaded with delay counter
; requires instatiation of RS_delays

RS_delay macro cycles
 local c
  if( cycles < 0 )
	error  "Negative delay requested"
  else
  if( cycles == 0 )  
  else
  if( cycles == .1 )
	nop  
  else
  if( cycles == .2)
	nope  
  else
  if( cycles == .3)
	nope	  
	nop
  else  
  if( cycles <= .8)
	call RS_DELAY#v(cycles)IC
RS_DELAYNEEDED set RS_DELAYNEEDED | (1 << cycles)
  else
c = (cycles / .4) - .1
  if( c > .255 )
	error  "Too long delay requested"
  endif
	movlw	#v(c)
c = cycles & .3
RS_DELAYNEEDED set RS_DELAYNEEDED | (0x8000 >> c)
	call RS_DELAY#v(c)WC
  endif 
  endif
  endif
  endif
  endif
  endif
 endm

;------------------------------------------------------------
; This macro instantiates delay routines, used in code, 
; generated by RS_delay

RS_delays macro
  if( RS_DELAYNEEDED & 0xF000 )
	if (RS_DELAYNEEDED & 0x1000 )  
RS_DELAY3WC				; 0x1000
	nop 
    endif		
	if (RS_DELAYNEEDED & 0x3000 )  
RS_DELAY2WC				; 0x2000
	nop 
    endif		
	if (RS_DELAYNEEDED & 0x7000 )  
RS_DELAY1WC				; 0x4000
	nop 
    endif		
RS_DELAY0WC				; 0x8000
	addlw	-.1			; 2
	skpz				; 3
	goto	RS_DELAY0WC	; 4
	return				;
  endif

  local i, d
i = .8
d = 0
  while( i >= .4 )    
   if( RS_DELAYNEEDED & (1 << i))
RS_DELAY#v(i)IC
d = .1
   endif
d = d && (i > .4 )
i--
   if( d )
    if( RS_DELAYNEEDED & (1 << i))
	nop	  
    else
i--
	if( i >= .4)
	nope
	else
	nop
	endif
	endif
   endif
  endw
  if( RS_DELAYNEEDED & 0x1FF )
	return 
  endif
 endm


; This procedure uses port driving method suggested by Regulus Berdin
; http://www.piclist.com/techref/microchip/rs232at500kbps.htm
; this macro generates code for short bit length: 2 - 9 cycles
; Code length:
; 	maximum = 8 + 4*bits; (RS_CYCLESPERBIT = 5)
; 	minimum = 5 + 2*bits; (RS_CYCLESPERBIT = 2)
;   average = 6 + 3*bits
RS_bodySEND2_9 macro speed, bits, port, pin, spacelvl
TX_SPACE_LEVEL equ spacelvl
    local i, d
	rrf     RS_DATA, W		; prepare data for output:
	xorwf   RS_DATA, F		; '1' in RS_DATA means toggle port
	movlw   (1 << pin)  	; load port-toggling mask
  if( spacelvl )
	bsf		port, pin 		; 0: sending start bit
  else
	bcf 	port, pin		; 0: sending start bit
  endif
   if ( RS_BITALIGNMENT & 1 )
	RS_delay (RS_CYCLESPERBIT - .1)
   else
	RS_delay (RS_CYCLESPERBIT - .2)
   endif				
i = 0
  while( i < bits )  	
   if( i == 0 )
    skpnc					; 1: first bit is already in C
   else
	btfsc	RS_DATA,#v(i-.1); 1: test data
   endif
	xorwf   port, F        	; 2: send bit
i++		
   if( i == bits )
d = .1						; last bit delay
   else
d = .0
   endif 
   if ( RS_BITALIGNMENT & (1 << i) )
	RS_delay (RS_CYCLESPERBIT - .1 + #v(d))
   else
	RS_delay (RS_CYCLESPERBIT - .2 + #v(d))
   endif				
  endw
 endm

; this macro generates code for long bit length: 10 and more cycles
RS_bodySEND10_H macro speed, bits, port, pin, spacelvl
  local looplen, startlen
	clrc					; C will be rolled in
  if( spacelvl )
	bsf		port, pin 		; 0: sending start bit
  else
	bcf 	port, pin		; 0: sending start bit
  endif
	rlf     RS_DATA, W		; 1: prepare data for output:
	xorwf   RS_DATA, F		; 2: '1' in RS_DATA means toggle port
	movlw	bits			; 3: load bit count
	movwf	RS_COUNT		; 4: into counter
  if ( (RS_BITALIGNMENT >> .1) == 0  || RS_CYCLESPERBIT > .450 )
looplen  = .7				; alignment not required, loop is 7 cycles long
startlen = .8
  else
	movlw	RS_BITALIGNMENT >> .1 ; 5: load alignment bits, not including start bit
	movwf	RS_ALIGN		; 6: load to alignment rotation file
looplen  = .10				; alignment required, loop is 10 cycles long
startlen = .10
  endif
	RS_delay (RS_CYCLESPERBIT - startlen + (RS_BITALIGNMENT & .1)) ; 7: the start bit aligned here
RS_#v(speed)BIT
	movlw   (1 << pin)  	; 7: load port-toggling mask
	rrf		RS_DATA, F		; 8: put data bit into C
	skpnc					; 9: test data bit
	xorwf   port, F        	; 10: send bit
  if ( looplen  == .10 )
	rrf		RS_ALIGN, F		; 1: rotate align bits
	skpnc					; 2: align if indicated
	nope					; 3: this instruction alings the cycle
  endif
	RS_delay (RS_CYCLESPERBIT - looplen); 4/5: loop is 10 (7) cycle long
	decfsz	RS_COUNT,F  	; 4/5:
	goto	RS_#v(speed)BIT ; 5/6:
	RS_delay .4				; 6
 endm

RS_bodyRECEIVE2_9 macro speed, bits, port, pin, spacelvl, file, expire, delay
 local i, c
i = 0
c = RS_CYCLESPERBIT + RS_HALFCYCLE + (RS_BITALIGNMENT & 1) - expire
 if( c >= 0 )
	RS_delay c
 endif
  
 while( i < bits )
  if( c >= 0 )
   if( spacelvl )
	btfss	port, pin		; 1: test data on port, pin
  else
	btfsc 	port, pin		; 1: test data on port, pin
  endif
	bsf		file, #v(i)		; 2: set data bit
i++
   if( i < bits )			; no delay for the last bit
    if ( RS_BITALIGNMENT & (1 << i) )
	RS_delay (RS_CYCLESPERBIT - .1)	
    else
	RS_delay (RS_CYCLESPERBIT - .2)
    endif
   endif
  else
	messg	Too many cycles expired (#v(expire)), can not read bit #v(i) in RS_RECEIVE#v(speed)
i++
c = c + RS_CYCLESPERBIT
    if ( RS_BITALIGNMENT & (1 << i) )
c++	
    endif
    if( c >= 0 )
	RS_delay c
    endif
  endif
  endw						; exits one cycle after last bit middle
	RS_delay   RS_HALFCYCLE + delay - .1
 endm

RS_bodyRECEIVE12_H macro speed, bits, port, pin, spacelvl, file, expire, delay
 local i, c, looplen, startlen
  if ( (RS_BITALIGNMENT >> .1) == 0  || RS_CYCLESPERBIT > .450 )
looplen = .9
startlen = .4
  else
looplen = .12
startlen = .6
 endif
i = 0
c = RS_CYCLESPERBIT + RS_HALFCYCLE + (RS_BITALIGNMENT & 1) - expire - startlen
  if( c >= 0 )
	RS_delay c				; expiring start bit and half of first bit
c = .0
	movlw	bits			; 1: load bit count
	movwf	RS_COUNT		; 2: into counter
  else
c = c + .2  
	messg   Too many cycles expired (#v(expire)) for RECIEVE#v(speed). "RS_COUNT" not loaded
  endif  
  if ( looplen == .10 )
   if( c >= .0 )
	RS_delay c
c = .0
	movlw	RS_BITALIGNMENT >> 1 ; 3: load alignment bits, not including start bit
	movwf	RS_ALIGN			 ; 4: into alignment rotation file
   else
	messg   Too many cycles expired (#v(expire)) for RS_RECIEVE#v(speed). "RS_ALIGN" not loaded
c = c + .2
   endif 
  endif
  if( c < 0 )
	error   Too many cycles expired (#v(expire)) for RS_RECIEVE#v(speed).
  else
	RS_delay c
  endif
RS_#v(speed)_BIT			; data reading loop
	clrc					; 1:
  if( spacelvl )
	btfss	port, pin		; 2: test data
  else
	btfsc 	port, pin		; 2: test data
  endif
	setc					; 3: set data bit in C
	rrf		file, F			; 4: roll-in the databit from C into RS_DATA		
	decf	RS_COUNT,F  	; 5:
	skpnz					; 6:
	goto	RS_#v(speed)_STOP ;7
  if( looplen == .10 )
	rrf		RS_ALIGN, F		; 8: rotate align bits
	skpnc					; 9: align if indicated
	nope					; 10: this instruction alings the cycle
  endif
	RS_delay (RS_CYCLESPERBIT - looplen); loop is 12 cycles long
	goto	RS_#v(speed)_BIT; 11:
RS_#v(speed)_STOP			; exits 7 cycles after last bit middle
c=.7
  if(bits < .8)				; if there were less than 8 bits, 
i=.8
	clrc
  while(i>bits)
	rrf		file, F			; fill most significant bits with zeros
i--
c++
  endw						
  endif
	RS_delay  RS_HALFCYCLE + delay - c
 endm

RS_DELAYNEEDED set 0

; RS_bodyRECEIVE generates RS_RECEIVE routine body
; speed    - baud rate (57600, 115200, etc.)
; bits     - data bits (5..8)
; port     - input port (PORTA, PORTB, etc)
; pin      - RX pin on the port (0..7)
; spacelvl - Port level (0..1) driven by SPACE (+V) on the interface line
; file     - file register where data is placed
; expire   - number of IC expired since start bit rasing edge
; delay	   - number of IC to expire after stop bit is estimated (negative allowed)
RS_bodyRECEIVE macro speed, bits, port, pin, spacelvl, file, expire, delay
	RS_calcCONST speed, bits, 1
  if(RS_CYCLESPERBIT + RS_HALFCYCLE < .4)
	error Baud rate #v(speed) is to high for frequency #v(CLOCK)
  endif
  if( (RS_CYCLESPERBIT < .12) || (RS_CYCLESPERBIT < .24 && RS_CYCLESPERBIT + RS_HALFCYCLE - expire < .6) )
	RS_bodyRECEIVE2_9 speed, bits, port, pin, spacelvl, file, expire, delay
  else
	RS_bodyRECEIVE12_H speed, bits, port, pin, spacelvl, file, expire, delay
  endif
 endm

; RS_bodySEND generates RS_SEND routine
; speed    - baud rate (57600, 115200, etc.)
; bits     - data bits (5..8)
; port     - output port (PORTA, PORTB, etc)
; pin      - TX pin on the port (0..7)
; spacelvl - Port level (0..1) that drives SPACE (+V) on the interface line
RS_bodySEND macro speed, bits, port, pin, spacelvl
	RS_calcCONST speed, bits, 0
	movwf	RS_DATA			; put data to rotation buffer
  if(RS_CYCLESPERBIT < .3)
	error Baud rate #v(speed) is to high for frequency #v(CLOCK)
  endif
  if(RS_CYCLESPERBIT < .10)
	RS_bodySEND2_9 speed, bits, port, pin, spacelvl
  else
	RS_bodySEND10_H speed, bits, port, pin, spacelvl
  endif
  if( spacelvl )
	bcf		port, pin 		; 2: sending stop bit
  else
	bsf 	port, pin		; 2: sending stop bit
  endif
 endm

;-------------------------------------------------------------
; RS RTS/CTS physical primitives
; CTS, RTS must be defined externally
; CTS_SPACE_LEVEL (0..1) defines logicla SPACE level for CTS
; RTS_SPACE_LEVEL (0..1) defines logicla SPACE level for RTS

#ifdef CTS_SPACE_LEVEL
CTS_setMARK  macro 
  if( CTS_SPACE_LEVEL )
  	bcf CTS
  else
  	bsf CTS
  endif
  endm
  
CTS_setSPACE  macro 	
  if( CTS_SPACE_LEVEL )
	bsf CTS
  else
	bcf CTS
  endif
  endm
#else			; empty macro in CTS is not used
CTS_setMARK  macro 
  endm
CTS_setSPACE  macro 	
  endm
#endif

#ifdef RTS_SPACE_LEVEL
RTS_skpMARK  macro 	
  if( RTS_SPACE_LEVEL )
  	btfsc RTS	; skip if RTS is high
  else  
  	btfss RTS	; skip if RTS is high
  endif
  endm 
  
RTS_skpSPACE  macro 	
  if( RTS_SPACE_LEVEL )
  	btfss RTS	; skip if RTS is low
  else
  	btfsc RTS	; skip if RTS is low
  endif
  endm
#endif

file: /Techref/member/eugene-ksf-/index.htm, 18KB, , updated: 2003/9/27 03:58, local time: 2024/11/12 16:53, owner: eugene-ksf-,

^{13.59.126.25:LOG IN}

©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?

Please DO link to this page! Digg it! / MAKE!

<A HREF="http://sxlist.com/TECHREF/member/eugene-ksf-/index.htm"> Member Homepage for eugene-ksf-</A>