please dont rip this site
MATHS.INC from PIC Microcontoller Input / Output Methods for Perminant Magnet Motors

;*******************************************************************
;                       Double Precision Multiplication
;
;               ( Optimized for Speed : straight Line Code )
;
;*******************************************************************;
;   Multiplication : ACCb(16 bits) * ACCa(16 bits) -> ACCb,ACCc ( 32 bits )
;      (a) Load the 1st operand in location ACCaLO & ACCaHI ( 16 bits )
;      (b) Load the 2nd operand in location ACCbLO & ACCbHI ( 16 bits )
;      (c) CALL D_mpy
;      (d) The 32 bit result is in location ( ACCbHI,ACCbLO,ACCcHI,ACCcLO )
;*******************************************************************;
;
;       multiplication macro
;
mulMac  MACRO
	LOCAL   NO_ADD
;
	rrf     ACCdHI, F       ;rotate d right
	rrf     ACCdLO, F
	btfss   STATUS,C    ;need to add?
	goto    NO_ADD          ; no addition necessary
	movf    ACCaLO,w        ; Addition ( ACCb + ACCa -> ACCb )
	addwf   ACCbLO, F       ;add lsb
	btfsc   STATUS,C    ;add in carry
	incf    ACCbHI, F
	movf    ACCaHI,w
	addwf   ACCbHI, F       ;add msb
NO_ADD  rrf     ACCbHI, F
	rrf     ACCbLO, F
	rrf     ACCcHI, F
	rrf     ACCcLO, F
;
	ENDM
;
;*******************************************************************;
;               Double Precision Multiply ( 16x16 -> 32 )
;         ( ACCb*ACCa -> ACCb,ACCc ) : 32 bit output with high word
;  in ACCb ( ACCbHI,ACCbLO ) and low word in ACCc ( ACCcHI,ACCcLO ).
;
D_mpyF                          ;results in ACCb(16 msb's) and ACCc(16 lsb's)
;
     IF   SIGNED
     CALL    S_SIGN
     ENDIF
;
	call    setup
;
; use the mulMac macro 16 times
;
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
	mulMac
;
    IF    SIGNED
	btfss   sign,MSB
	retlw   0
	comf    ACCcLO          ; negate ACCa ( -ACCa -> ACCa )
	incf    ACCcLO
	btfsc   STATUS,Z
	decf    ACCcHI
	comf    ACCcHI
	btfsc   STATUS,Z
neg_B   comf    ACCbLO          ; negate ACCb
	incf    ACCbLO
	btfsc   STATUS,Z
	decf    ACCbHI
	comf    ACCbHI
	retlw   0
    ELSE
	retlw   0
    ENDIF
;*******************************************************************
setup   movlw   .16             ; for 16 shifts
	movwf   temp
	movf    ACCbHI,w          ;move ACCb to ACCd
	movwf   ACCdHI
	movf    ACCbLO,w
	movwf   ACCdLO
	clrf    ACCbHI
	clrf    ACCbLO
	retlw   0
;*******************************************************************
;  Assemble this section only if Signed Arithmetic Needed
;
     IF    SIGNED
;
S_SIGN  movf    ACCaHI,W
	xorwf   ACCbHI,W
	movwf   sign
	btfss   ACCbHI,MSB        ; if MSB set go & negate ACCb
	goto    chek_A
;
	comf    ACCbLO          ; negate ACCb
	incf    ACCbLO
	btfsc   STATUS,Z
	decf    ACCbHI
	comf    ACCbHI
;
chek_A  btfss   ACCaHI,MSB        ; if MSB set go & negate ACCa
	retlw   0
	goto    neg_A
;
     ENDIF
;
;*******************************************************************
;                       Double Precision Division
;
;               ( Optimized for Speed : straight Line Code )
;
;*******************************************************************;
;   Division : ACCb(16 bits) / ACCa(16 bits) -> ACCb(16 bits) with
;                                               Remainder in ACCc (16 bits)
;      (a) Load the Denominator in location ACCaHI & ACCaLO ( 16 bits )
;      (b) Load the Numerator in location ACCbHI & ACCbLO ( 16 bits )
;      (c) CALL D_div
;      (d) The 16 bit result is in location ACCbHI & ACCbLO
;      (e) The 16 bit Remainder is in locations ACCcHI & ACCcLO
;*******************************************************************;
;
divMac  MACRO
	LOCAL   NOCHK
	LOCAL   NOGO
	bcf     STATUS,C
	rlf     ACCdLO, F
	rlf     ACCdHI, F
	rlf     ACCcLO, F
	rlf     ACCcHI, F
	movf    ACCaHI,w
	subwf   ACCcHI,w          ;check if a>c
	btfss   STATUS,Z
	goto    NOCHK
	movf    ACCaLO,w
	subwf   ACCcLO,w        ;if msb equal then check lsb
NOCHK   btfss   STATUS,C    ;carry set if c>a
	goto    NOGO
	movf    ACCaLO,w        ;c-a into c
	subwf   ACCcLO, F
	btfss   STATUS,C
	decf    ACCcHI, F
	movf    ACCaHI,w
	subwf   ACCcHI, F
	bsf     STATUS,C    ;shift a 1 into b (result)
NOGO    rlf     ACCbLO, F
	rlf     ACCbHI, F
	ENDM

;*******************************************************************
;       Double Precision Divide ( 16/16 -> 16 )
;
;         ( ACCb/ACCa -> ACCb with remainder in ACCc ) : 16 bit output
; with Quotiont in ACCb (ACCbHI,ACCbLO) and Remainder in ACCc (ACCcHI,ACCcLO).
;
;   NOTE  :  Before calling this routine, the user should make sure that
;            the Numerator(ACCb) is greater than Denominator(ACCa). If
;            the case is not true, the user should scale either Numerator
;            or Denominator or both such that Numerator is greater than
;            the Denominator.
;*******************************************************************
neg_A   comf    ACCaLO, F          ; negate ACCa ( -ACCa -> ACCa )
	incf    ACCaLO, F
	btfsc   STATUS,Z
	decf    ACCaHI, F
	comf    ACCaHI, F
	retlw   0
;*******************************************************************

D_divF
     IF   SIGNED
     CALL    S_SIGN
     ENDIF
	call    setup
	clrf    ACCcHI
	clrf    ACCcLO
; use the mulMac macro 16 times
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
	divMac
;
    IF    SIGNED
	btfss   sign,MSB        ; check sign if negative
	retlw   0
	goto    neg_B          ; negate ACCa ( -ACCa -> ACCa )
    ELSE
	retlw   0
    ENDIF
;
;*******************************************************************
;  Assemble this section only if Signed Arithmetic Needed
;
     IF    SIGNED
;
S_SIGN  movf    ACCaHI,W
	xorwf   ACCbHI,W
	movwf   sign
	btfss   ACCbHI,MSB        ; if MSB set go & negate ACCb
	goto    chek_A
;
	comf    ACCbLO          ; negate ACCb
	incf    ACCbLO
	btfsc   STATUS,Z
	decf    ACCbHI
	comf    ACCbHI
;
chek_A  btfss   ACCaHI,MSB        ; if MSB set go & negate ACCa
	retlw   0
	goto    neg_A
;
     ENDIF
;
;*******************************************************************
;                 Double Precision Addition & Subtraction
;*******************************************************************;
;   Addition :  ACCb(16 bits) + ACCa(16 bits) -> ACCb(16 bits)
;      (a) Load the 1st operand in location ACCaLO & ACCaHI ( 16 bits )
;      (b) Load the 2nd operand in location ACCbLO & ACCbHI ( 16 bits )
;      (c) CALL D_add
;      (d) The result is in location ACCbLO & ACCbHI ( 16 bits )
;*******************************************************************;
;   Subtraction : ACCb(16 bits) - ACCa(16 bits) -> ACCb(16 bits)
;      (a) Load the 1st operand in location ACCaLO & ACCaHI ( 16 bits )
;      (b) Load the 2nd operand in location ACCbLO & ACCbHI ( 16 bits )
;      (c) CALL D_sub
;      (d) The result is in location ACCbLO & ACCbHI ( 16 bits )
;*******************************************************************;
D_sub   call    neg_A           ; At first negate ACCa; Then add
;*******************************************************************
D_add   movf    ACCaLO,w
	addwf   ACCbLO, F       ;add lsb
	btfsc   STATUS,C    ;add in carry
	incf    ACCbHI, F
	movf    ACCaHI,w
	addwf   ACCbHI, F       ;add msb
	retlw   0


file: /Techref/microchip/io/dev/motor/servob/MATHS_INC.htm, 7KB, , updated: 2005/5/13 16:50, local time: 2024/11/29 23:08,
TOP NEW HELP FIND: 
3.142.124.119:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://sxlist.com/Techref/microchip/io/dev/motor/servob/MATHS_INC.htm"> MATHS.INC</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to sxlist.com!


Site supported by
sales, advertizing,
& kind contributors
just like you!

Please don't rip/copy
(here's why

Copies of the site on CD
are available at minimal cost.
 

Welcome to sxlist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .