FLEX Paging I located some technical data on FLEX which I do not see on the Motorola website (http://www.motorola.com), so I will post it here. This information is from an 8/93 Motorola introductory manual titled "An Introduction to FLEX(tm)". A brief restatement of the contents follows. FLEX can start at 1600 BPS bippolar FSK, and then upgrade to higher speeds when system upgrades permit. FLEX pagers can accept 1600, 3200 and 6400 BPS speeds without changes. FLEX systems can dynamically change data speed during times of peak demand, the optimum speed being the lowest which meets traffic demand. FLEX has a binary message mode which permits message encryption. (I have never examined this encryption feature.) The document says FLEX is compatible with existing protocols, but APOC was not known when it was published. (Most probably there are ways to combine them on a channel if necessary.) FLEX pagers must see FLEX sync at least once per minute, and channel sharing must be synchronized. Increased data speed requires more transmitters for comparable coverage. Compared to 1200 BPS POCSAG, 1600 BPS FLEX requires about 1.2 times as many transmitters, 2400 BPS POCSAG requires about 1.4 times as many transmitters, 3200 BPS FLEX requires about 1.8 times as many transmitters, and 6400 BPS FLEX requires about twice as many transmitters. FLEX operates on a 4-minute overall cycle. During this 4 minutes, there are 128 frames of 1.875 second each. Each of these frames contains a 1600 BPS sync header, followed by 10 data blocks. At 1600 BPS, these blocks are 256 bits in size. At 3200 BPS, they are 512 bits in size, and at 6400 BPS they are 1024 bits in size. The blocks contain information arranged as 1, 2 or 4 groups of eight 32-bit BCH codewords each. Motorola refers to the coding as (32,21)BCH code. Each 32-bit codeword contains 21 bits of data and 11 bits of error correction data. The groups of eight codewords are stacked in rows but transmitted by columns, which interleaves the data. At 1600 BPS, each block consists of eight 32-bit codewords, or 256 bits, and these bits are transmitted as 1600 BPS bipolar FSK. At 3200 BPS, each block consists of 512 bits from two multiplexed eight-codeword groups, and these bits are transmitted as 4-FSK at 1600 symbols per second. At 6400 BPS, each block consists of 1024 bits from four multiplexed eight-codeword groups, and these bits are transmitted as 4-FSK at 3200 symbols per second. At the receiving end, the data is demuxed and de-interleaved into the original groups of eight codewords and then BCH checked; up to 2 errors in each 32-bit codeword can be corrected. The breaking up of data into interleaved blocks is done for error management purposes only. The 10 groups of 8 codewords following the sync header carry a block information word, an address field, a vector field, a message data field, and any leftover space. These words and fields are contained in every frame following the sync header, but they do not necessarily align with the codeword-group boundaries. Addresses are carried first in each field, so pagers can "sleep" for the rest of the field if they are not being addressed. There can be unused leftover space after the message data field because the message lengths are variable and not all addresses require vectors, yet the 10 blocks must remain at their fixed sizes for synchronicity. Motorola says the leftover space is filled with idle codes. And at 3200 and 6400 BPS where two or four sub-frames are multiplexed into each transmitted frame, the block information words, the address, vector and data fields and the leftover space of each sub-frame are of independent sizes. The pagers can be programmed to monitor only some of the frames. The paging systems must of course be correspondingly programmed. By monitoring fewer frames, the pager can "sleep" more, increasing battery life where slower paging response can be tolerated. For example, if the pager monitors only every 32nd frame, there can be up to 60 seconds of additional delay (32 times 1.875 seconds per frame), but with substantial battery savings. If instead the pager monitors every fourth frame, the extra delay drops to 7.5 seconds (4 times 1.875 seconds per frame), but with less battery savings. Battery savings from 4 frame, 8 frame, 16 frame and 32 frame programmings are shown in the document. DISCLAIMER Not employed by or representing Motorola, not a shareholder of Motorola, etc. This post is for information purposes only; I am not promoting FLEX or any other format, although I am in favor the modern high speed formats because they permit better use of congested radio channels, and because they also offer improved battery life. More information on FLEX is available from Motorola at http://www.motorola.com. Bob Bruhns, WA3WDR, bbruhns@li.net
file: /Techref/pager/flex.txt, 4KB, , updated: 1999/9/3 11:47, local time: 2024/8/14 22:17,
18.224.43.250:LOG IN
|
©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://sxlist.com/TECHREF/pager/flex.txt"> pager flex</A> |
Did you find what you needed? |
Welcome to sxlist.com!sales, advertizing, & kind contributors just like you! Please don't rip/copy (here's why Copies of the site on CD are available at minimal cost. |
Welcome to sxlist.com! |
.